Micro heat adsorption dryer
2025.01.09
产品参数/ Product parameter
微热吸附式干燥机 |
||||||||
型号 | 处理空气量(Nm3/min) | 扩散器型号 | 接口尺寸 | 外形尺寸(mm) | 加热器功率(Kw) | 重量 （Kg) |
||
长 | 宽 | 高 |
||||||
HKS-4MXF | 4.5 | KS-40 | G1-1/2” | 1100 | 700 | 1770 | 3 | 180 |
HKS-6MXF | 6.2 | KS-40 | G1-1/2” | 1100 | 700 | 2140 | 4 | 380 |
HKS-8MXF | 8.5 | KS-50 | G2” | 1300 | 750 | 2010 | 4 | 460 |
HKS-10MXF | 11 | KS-50 | G2” | 1300 | 750 | 2170 | 6 | 500 |
HKS-13MXF | 13.5 | KS-50 | G2” | 1350 | 800 | 2210 | 6 | 560 |
HKS-15MXF | 17 | KS-65 | DN65 | 1400 | 850 | 2275 | 6 | 760 |
HKS-20MXF | 22 | KS-65 | DN65 | 1450 | 900 | 2300 | 9 | 930 |
HKS-25MXF | 27 | KS-80 | DN80 | 1500 | 900 | 2560 | 9 | 990 |
HKS-30MXF | 32 | KS-80 | DN80 | 1500 | 900 | 2575 | 12 | 1380 |
HKS-40MXF | 42 | KS-100 | DN100 | 1800 | 1100 | 2750 | 18 | 1620 |
HKS-50MXF | 50 | KS-100 | DN100 | 1900 | 1150 | 2800 | 21 | 1820 |
HKS-60MXF | 65 | KS-100 | DN100 | 1950 | 1200 | 2810 | 25 | 2320 |
HKS-80MXF | 85 | KS-125 | DN125 | 2200 | 1200 | 2865 | 30 | 2880 |
HKS-100MXF | 110 | KS-150 | DN150 | 2400 | 1200 | 2970 | 40 | 4230 |
HKS-130MXF | 140 | KS-150 | DN150 | 2675 | 1350 | 3150 | 50 | 5060 |
HKS-150MXF | 160 | KS-200 | DN200 | 2950 | 1500 | 3300 | 65 | 6350 |
HKS-180MXF | 185 | KS-200 | DN200 | 3200 | 1600 | 3460 | 72 | 6875 |
HKS-200MXF | 210 | KS-200 | DN200 | 3500 | 1750 | 3600 | 80 | 7400 |
HKS-230MXF | 240 | KS-200 | DN200 | 3750 | 1850 | 3700 | 80 | 8640 |
HKS-250MXF | 260 | KS-200 | DN200 | 4000 | 2000 | 3800 | 90 | 9510 |
Product principle introduction:
The micro heat adsorption dryer is an addition of a heater to the non heat adsorption dryer, combining the advantages of pressure swing adsorption and temperature swing adsorption. The regenerated product gas flow is used to heat and regenerate the desiccant after increasing the temperature, which can improve the regeneration effect and reduce the gas consumption of regeneration gas.
Standard technical parameters:
- Rated intake temperature: ≤ 40℃
- Rated working pressure: 0.6-1.0Mpa
- Environmental temperature: ≤ 45℃
- Dew point of air:- Customization accepted below 40 ℃ (0.7MPa) (-60 ℃)
- Regeneration gas consumption: 7-8%
- Pressure loss: ≤ 0.02MPa
- Inlet oil content: ＜ 0.1mg/m³
- Installation method: Indoor, no foundation, concrete floor leveling, reserved space for maintenance operations
- Adsorbent: Activated alumina, molecular sieve
- Power supply: 380V-3PH-50HZ
- Users can selectively configure customized products, and consult our technical service department for detailed technical parameters
Design features:
- Fully electronic programmable controller, user-friendly human-machine interface, automatic continuous display of twin tower working conditions
- Regenerative orifice plate technology effectively controls the regeneration flow rate
- Accurate movements, stable performance, and easy operation
- Professional rust prevention treatment is applied to the inner wall of the cylinder, which will not corrode for 10 years
- Stainless steel diffuser is corrosion-resistant, wear-resistant, and durable
- Stainless steel valves work reliably and have a lifespan of up to 500000 actions
- Equipped with high temperature protection device, low-power density stainless steel electric heater, high temperature control accuracy, low risk, long service life
- Use the adsorption tower heater as an insulation layer to reduce heat loss and energy consumption
- Variable frequency band delayed adsorption technology is more energy-efficient (optional)
Contact
Leave your information and we will contact you.
Phone
Mail