Non thermal adsorption dryer
2025.01.09
产品参数/ Product parameter
型号 | 处理空气量(Nm3/min) | 扩散器型号 | 接口尺寸 | 外形尺寸（mm） | 重量(KG) |
||
长 | 宽 | 高 |
|||||
HKS-4WXF | 4.5 | KS-40 | G1-1/2” | 1100 | 550 | 1710 | 160 |
HKS-6WXF | 6.2 | KS-40 | G1-1/2” | 1100 | 550 | 2080 | 350 |
HKS-8WXF | 8.5 | KS-50 | G2” | 1300 | 650 | 2110 | 430 |
HKS-10WXF | 11 | KS-50 | G2” | 1300 | 650 | 2110 | 460 |
HKS-13WXF | 13.5 | KS-50 | G2” | 1350 | 700 | 2150 | 520 |
HKS-15WXF | 17 | KS-65 | DN65 | 1350 | 750 | 2270 | 720 |
HKS-20WXF | 22 | KS-65 | DN65 | 1400 | 750 | 2285 | 890 |
HKS-25WXF | 27 | KS-80 | DN80 | 1450 | 750 | 2545 | 950 |
HKS-30WXF | 32 | KS-80 | DN80 | 1450 | 775 | 2555 | 1320 |
HKS-40WXF | 42 | KS-100 | DN100 | 1700 | 925 | 2595 | 1550 |
HKS-50WXF | 50 | KS-100 | DN100 | 1800 | 950 | 2700 | 1800 |
HKS-60WXF | 65 | KS-100 | DN100 | 1850 | 975 | 2700 | 2250 |
HKS-80WXF | 85 | KS-125 | DN125 | 2100 | 1030 | 2810 | 2810 |
HKS-100WXF | 110 | KS-150 | DN150 | 2600 | 1200 | 3020 | 4150 |
HKS-130WXF | 140 | KS-150 | DN150 | 2700 | 1200 | 3030 | 4980 |
HKS-150WXF | 160 | KS-200 | DN200 | 2950 | 1400 | 3250 | 6250 |
HKS-180WXF | 185 | KS-200 | DN200 | 3250 | 1450 | 3450 | 6460 |
HKS-200WXF | 210 | KS-200 | DN200 | 3600 | 1600 | 3500 | 7280 |
HKS-230 | 240 | KS-200 | DN200 | 3700 | 1700 | 3600 | 8520 |
HKS-250 | 260 | KS-200 | DN200 | 4000 | 1800 | 3800 | 9360 |
Product principle introduction:
The non heat adsorption dryer utilizes the principle of pressure swing adsorption, allowing the dryer to adsorb under pipeline pressure, and then desorb when switched to atmospheric pressure. About 12-14% of the dried product gas is introduced back from the dryer outlet to further purify and regenerate the desiccant. The twin towers alternate the above process and provide dry compressed air to the gas points.
Standard technical parameters:
- Rated intake temperature: ≤ 40℃
- Rated working pressure: 0.6-1.0Mpa
- Environmental temperature: ≤ 45℃
- Dew point of air:- 40 ℃ (0.7MPa) (Customization accepted below -60 ℃)
- Regeneration gas consumption: 12-14%
- Pressure loss: ≤ 0.02MPa
- Inlet oil content: ＜ 0.1mg/m³
- Installation method: Indoor, no foundation, concrete floor leveling, reserved space for maintenance operations
- Adsorbent: Activated alumina, molecular sieve
- Power supply: 220-1PH-50HZ
- Users can selectively configure customized products
Please consult our technical service department for detailed technical parameters
Design features:
- Short cycle adsorption cycle, isothermal operation, preservation of adsorption heat, good natural desorption effect
- Fully electronic programmable controller, user-friendly human-machine interface, automatic continuous display of twin tower working conditions
- Regenerative orifice plate technology effectively controls the regeneration flow rate
- Accurate movements, stable performance, and easy operation
- Professional rust prevention treatment is applied to the inner wall of the cylinder, which will not corrode for 10 years
- Stainless steel diffuser is corrosion-resistant, wear-resistant, and durable
- Stainless steel valves work stably and have a lifespan of up to 500000 actions
- Optimize the valve form to ensure the feasibility and convenience of on-site maintenance and replacement
- High flow muffler, lower back pressure, no condensation concerns for muffler and exhaust passage
- Variable frequency band delayed adsorption technology is more energy-efficient (optional)
Contact
Leave your information and we will contact you.
Phone
Mail